AC Tonnage Calculator: what size air conditioner do you actually need?
A 1,500 sq ft home in a moderate US climate needs about a 2.5-ton (30,000 BTU) air conditioner on this site’s planning estimate — but climate, sun exposure, ceilings and insulation can shift that by a full ton. Enter your real room data below to get the exact tonnage, BTU and running cost.
Estimate only — confirm equipment sizing with a Manual J load calculation by a licensed contractor.
| Cooling load | — |
| Thermal power | — |
| Floor area | — |
| Duct airflow needed | — |
All Calculators
Every tool runs entirely in your browser. No accounts, no uploads, no tracking of your inputs.
Model Number → Tonnage Decoder
Paste your AC's model number (Goodman, Carrier, Trane, Voltas, LG…) and we'll decode its tonnage from the capacity code; Indian brands are checked against the BEE star label.
→ TOOL · 03Whole-House Calculator
Add every room, sum the loads, and get a central-system size or per-room split AC plan — no signup required.
→ TOOL · 04AC Electricity Bill Calculator
Monthly running cost from tonnage, star rating / SEER2, daily hours and your local tariff.
→ TOOLFurnace Size Calculator
Heat loss at your county’s winter design temperature, and the furnace output range ENERGY STAR allows.
→ TOOLHeat Pump Size Calculator
Cooling-anchored sizing with balance point and backup heat for your county.
→ TOOLSEER2 Savings Calculator
Yearly savings and payback from a higher-efficiency AC or heat pump.
→ TOOL · 05BTU ⇄ Tons ⇄ kW Converter
Instant conversions between BTU/hr, refrigeration tons, kilowatts, kcal/hr and horsepower.
→ TOOL · 06Portable AC (SACC) Calculator
Portable units carry more than one capacity figure. Size by the DOE's derated SACC rating instead.
→ TOOL · 07AC Ampere Calculator
Estimated running amps by tonnage, and how the nameplate MCA and MOCP set the wire and breaker.
→ TOOL · 08Mini-Split Calculator
Per-zone ductless sizing with multi-zone totals, from 6,000 BTU bedrooms to 36,000 BTU open plans.
→ TOOL · 09Window AC Calculator
Right-size a 5,000–34,000 BTU window unit for a single room without overshooting.
→ TOOL · 10Commercial Tonnage Calculator
Offices, shops and server rooms — heavier occupant and equipment loads handled properly.
→TOOL · 11Duct Size & CFM Calculator
Airflow (CFM) and round or rectangular duct sizing by system tonnage and duct role.
→Quick Sizing Chart
Typical size by home area — moderate US climate (Zone 3), average insulation, 8 ft ceilings. Sizes are the standard sizes within 90–115% of the load (ENERGY STAR’s recommended range); loads are this site’s planning estimate.
| Area | Cooling load | AC size |
|---|---|---|
| 600 sq ft (one room) | 13,200 BTU/hr | 12,000–14,000 BTU room unit |
| 1,000 sq ft | 21,000 BTU/hr | 2 ton |
| 1,500 sq ft | 29,500 BTU/hr | 2.5 ton |
| 2,000 sq ft | 37,800 BTU/hr | 3–3.5 ton |
| 2,500 sq ft | 45,800 BTU/hr | 3.5–4 ton |
| 3,000 sq ft | 53,800 BTU/hr | 5 ton |
Detailed pages by size: 200 · 300 · 400 · 500 · 600 · 800 · 1,000 · 1,200 · 1,500 · 1,600 · 1,800 · 2,000 · 2,500 · 3,000 sq ft · full chart
Sizing by Space
Garages, sunrooms, server rooms and classrooms don't follow bedroom math — each page below explains that space's load physics with a calculator pre-tuned for it.
Garage
A two-car garage carries loads a same-size bedroom never sees: the envelope is usu…
→SPACEGarage Gym
ENERGY STAR’s room AC chart allows 600 BTU/hr per extra person at rest; someone mid-workout puts out more, so a home gym needs far more cooling than its size suggests…
→SPACEBedroom
Low internal gains (two sleeping people, no appliances), night-time operation when outdoor temp…
→SPACELiving Room
A living room's load swings more than any other room: two people watching TV on a Tuesday, ten …
→SPACEKitchen
Cooking appliances dump roughly 4,000 BTU/hr of ambient heat into the room while in use — a gas…
→SPACESunroom
Standard sizing assumes walls that resist heat; a sunroom's envelope is designed to admit it. S…
→SPACEAttic Room / Loft Conversion
An attic room doesn't sit under a roof — it sits inside one. Heat soaks through the sl…
→SPACEBasement
Below-grade walls sit against cool earth — a basement's sensible cooling load is a fraction of…
→SPACEHome Office
A desktop workstation, two monitors and peripherals turn their power draw into heat — 3.412 BTU/hr per watt…
→SPACEServer Room / IT Closet
Electronics turn nearly all input power into heat, so server rooms are sized on equipment watts (BTU/hr = watts × 3.412), not floor area…
→SPACERetail Shop
Retail loads stack three things homes don't: door-opening infiltration every few minutes (a gla…
→SPACERestaurant Dining Area
A seated diner adds ~600 BTU/hr; a full 24-cover dining room carries roughly 13,000 BTU/hr of extra load from people, lighting and kitchen heat…
→SPACESalon / Parlour
A hair dryer is a heat gun — every watt it draws adds 3.412 BTU/hr while running. With two or three…
→SPACEGym / Fitness Studio
Fifteen people training add a heavy load of body heat and a torrent of…
→SPACEClassroom / Coaching Centre
A classroom is the purest occupancy-driven load: 30 students at 600 BTU each (ENERGY STAR’s per-person figure) is about 18,000 BTU/hr before sun and equipment…
→SPACEMobile / Manufactured Home
Manufactured homes stack several load multipliers at once, starting with thin wall cavities…
→SPACEConservatory
A conservatory is glazing on five of six surfaces — including the roof, the worst one. Summer s…
→SPACEStudy / Small Room
A 90 sq ft study with one occupant and a laptop carries one of the lightest loads in the house …
→Frequently Asked Questions
Straight answers, sized for both US central systems and Indian split ACs.
How many square feet does 1 ton of AC cool?
In a moderate US climate, 1 ton (12,000 BTU/hr) cools roughly 450-550 sq ft of average-insulated space. In India mode, this site’s planning estimate puts 1 ton at a room of about 115 sq ft in hot cities, about 125 sq ft in composite ones and about 155 sq ft in Bengaluru (9.5 ft ceiling, 3 people).
What happens if my AC is oversized?
An oversized unit cools the air quickly but shuts off before removing humidity — a behavior called short-cycling. You get a cold, clammy room, more compressor wear, and a higher bill.
How do I find the tonnage of my existing AC?
It's coded in the outdoor unit's model number, not the serial number. Look for a two-digit group like 18, 24, 30, 36, 42, 48 or 60 — capacity in thousands of BTU; divide by 12 for tons. Our Model Number Decoder does this for 13 US brands using each maker's own published key.
Is this a Manual J calculation?
No. It is this site’s planning estimate, built from area, climate, ceiling height, sun, insulation, occupants, windows and doors; it does not follow Manual J’s method. A licensed contractor should run a full Manual J before you buy a central system.
Method & standards
This calculator uses this site’s planning estimate (area, climate zone, ceiling, sun, insulation, occupants, windows and doors), not an ACCA Manual J calculation. For final central-system sizing, a full ANSI/ACCA 2 Manual J is the standard — ACCA.
Updated 6 November 2026